logo lang_icon

KOR

UCL SWIFT

본문 바로가기
쇼핑몰 전체검색

전체메뉴

회원로그인

회원가입

오늘 본 상품 0

없음

UCL SWIFT

회원로그인

회원가입

Fusion Splice-On Connector

← Scroll left and right →

ftth0102_img01

The fusion splice-on connector is field installable and provides easy quick, reliable, permanent field terminations, complying with international standards, such as IEC 61300 series, and Telcordia GR-326-CORE/GR-1081-CORE. It provides more stable quality and performance than that of mechanical field installable types of connectors. Its fiber and field fiber from drop/patchcord cable can be aligned and spliced by using fusion splicers to terminate any types of fibers in the optical cable. The splice point is protected with heat shrink protection sleeve and located in the connector body. It allows installers to reduce service delivery/operation and maintenance time. The fusion splice-on connector (FSOC) is quick, easy and reliable solution for the last mile of FTTH (Fiber to the Home) and data center area. As it is field installable, it eliminates excess cable length and because of fusion splicing, there is no need of field mountable connector which requires high precision skills.

← Scroll left and right →

ftth0102_img02
  • Features
  • Structure
  • Optical Performance
  • Other Performances

← Scroll left and right →

Field installable technology.

Superior optical, mechanical and environmental performance.

Splicing point and its protective tube located inside the connector.

No cable slack required.

Strong tensile (4.5~6.8kgf) enables outdoor deployment.

Improvement of quality and reliability reduces maintenance cost and labor cost dramatically.

Reduction of installation cost.

Field stripping available for the SOC.

Pre-stripped/pre-cleaved available optionally.

Compliant with Telcordia GR-326-CORE.

← Scroll left and right →

The fusion splice-on connector has many types such as SC, LC, ST and FC, consisting of ferrule assembly, protected fiber stub of defined length, housing, stop ring, protection sleeve, boot and so on. Below figure shows the structure and its components.

ftth0101_img01

The typical loss of the physical contact mated in the adapter can be 0.1 dB. Fusion splicing attenuation is typically 0.02 dB, and maximum is 0.05 dB. Therefore total expected loss is in the range of 0.12 dB to 0.15 dB. Expected return loss is over 55dB (UPC) and over 60dB (APC) respectively. It can be adapted to analog networks (≥55dB) with no signal interference and no noise. Types of the alignment methods are IPAAS Core, Fixed V-groove and Active clad. Most importantly, fiber angles and cleaved fiber ends can be seen on the fusion splicer while splicing and the splicing point can be protected with heat shrinkable tubes.

← Scroll left and right →

Process Specifications (at 1310nm and 1550nm)
Insertion Loss Avg. ≤0.2dB
Max. ≤0.3dB
Return Loss Min. >50dB (UPC), >60dB (APC)


← Scroll left and right →

Test Conformance Method / Condition Specifications
Mating Durability IEC 61300-2-2 / GR-326-CORE, 4.4.3.8 No. of cycles: 200 Loss Increase ≤ 0.3dB
Return Loss Decrease ≤ 5dB
Vibration IEC 61300-2-1 / GR-326-CORE, 4.4.3.1 Freq. Range: 10Hz ~ 55Hz
Duration: 2h/axis
Sweep rate: 1 octave/min
Amplitude: 1.5mm
Loss Increase ≤ 0.3dB
Return Loss Decrease ≤ 5dB
Impact IEC 61300-2-12 / GR-326-CORE, 4.4.3.7 8 drops
1.5m drop height
Loss Increase ≤ 0.3dB
Return Loss Decrease ≤ 5dB
Proof
(2.0mm/3.0mm Cord Types only)
IEC 61300-2-51 / GR-326-CORE, 4.4.3.5 Straight pull, 0°, 6.8kgf, 5 sec / Side pull, 90°, 2.3kgf, 5 sec Loss Increase ≤ 0.5dB
Return Loss Decrease ≤ 5dB
Transmission with Applied Tensile Load
(2.0mm/3.0mm Cord Types only)
GR-326-CORE, 4.4.2.2 Loads: 2.0kgf at 0°/90°, 0.25kgf at 135° Loss Increase ≤ 0.3dB
Return Loss Decrease ≤ 5dB
Thermal Cycle GR-326-CORE, 4.4.2.2 -40°C±2°C to 75°C±2°C, 21 cycles, Dwell time: 1 hr at 23°C±2°C, Transition time: 1 hr Loss Increase ≤ 0.3dB
Return Loss Decrease ≤ 5dB
End face Geometry Telcordia GR-326-CORE, 4.4.5 Interferometer measurement Apex offset: <50μm
Radius of Curvature: 7~25mm (UPC) / 5~12mm(APC)
Undercut/Protrusion:
UPC: Undercut: -0.02R3+1.3R2-31R+325, Protrusion: ≤50nm,
APC: Undercut/Protrusion ≤100nm
APC Angular Tolerance: 7.850~8.050 degree


Type Details

  • SC
  • LC
  • FC
  • ST

← Scroll left and right →

 Model

 Image

Description

Specifications

 FSOC-SC-09

  

SC type

Polishing type: UPC, APC

Fiber type: SM, MM

Applicable cable diameter: 0.9mm

Dimensions: 57x9x8mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Click to download

 FSOC-SC-HB

  

SC Hard boot type

Polishing type: UPC, APC

Fiber type: SM, MM

Applicable cable: 2x3mm/3mm drop cables

Dimensions: 56.5x9x8mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Straight pull, 0°: 4.5kgf, Side pull, 90°: 2.3kgf

Click to download

 FSOC-SC-SB

  

SC Soft boot type

Polishing type: UPC, APC

Fiber type: SM, MM

Applicable cable: 2mm/3mm cords

Dimensions: 62x9x8mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Straight pull, 0°: 6.8kgf, Side pull, 90°: 2.3kgf

Click to download

← Scroll left and right →

 Model

 Image

 Description

 Specifications

 FSOC-LC-09

LC type

Polishing type: UPC, APC

Fiber type: SM, MM

Applicable cable diameter: 0.9mm

Dimensions: 45.7x10.3x5.5mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Click to download

 FSOC-LC-20

  

SC Soft boot type

Polishing type: UPC, APC

Fiber type: SM, MM

Applicable cable: 2mm cord

Dimensions: 62x9x8mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Straight pull, 0°: 6.8kgf, Side pull, 90°: 2.3kgf

Click to download

← Scroll left and right →

 Model

 Image

 Description

 Specifications

 FSOC-FC-09

 

FC type

Polishing type: UPC, APC

Fiber type: SM, MM

Applicable cable diameter: 0.9mm

Dimensions: 54x10x10mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Click to download

 FSOC-FC-30

  

FC Hard boot type

Polishing type: UPC, APC

Fiber type: SM, MM

Applicable cable: 3mm cord

Dimensions: 59x10x10mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Straight pull, 0°: 4.5kgf, Side pull, 90°: 2.3kg

Click to download

← Scroll left and right →

 Model

Image 

 Description

 Specifications

 FSOC-ST-09

  

ST 0.9mm type

Polishing type: UPC

Fiber type: SM, MM

Applicable cable diameter: 0.9mm

Dimensions: 61.3x9.6x9.6mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Click to download

 FSOC-ST-30

 

ST 30 boot type

Polishing type: UPC

Fiber type: SM, MM

Applicable cable: 3mm cord

Dimensions: 61.6x9.6x9.6mm

IL: Typ. 0.15dB, Max. 0.3dB

RL: SM: ≥55dB (UPC), ≥60dB(APC), MM: ≥30dB

Straight pull, 0°: 4.5kgf, Side pull, 90°: 2.3kgf

Click to download

사이트 정보

회사명 회사명 주소 OO도 OO시 OO구 OO동 123-45
사업자 등록번호 123-45-67890 대표 대표자명 전화 02-123-4567 팩스 02-123-4568
통신판매업신고번호 제 OO구 - 123호 개인정보 보호책임자 정보책임자명
부가통신사업신고번호 12345호

접속자집계

오늘
39
어제
432
최대
432
전체
15,403
Copyright © 2001-2013 회사명. All Rights Reserved.